|
Indoor
Sensors(Temperature,Humidity,CO,CO2) |
|
DSW series |
|
- |
Temperature element: RTD 100/0 (Pt100)
Accuracy: (0.1+0.0017|t|)
(DSW-100-TRx, -TRHx) |
- |
Humidity element: Electrostatic capacity variation type
Connector type for easy replacement
(DSW-100-Hx, -TxHx) |
- |
For temperature sensors with current output, the 2-wire type can be connected to Shinko controllers, resulting in cost reduction.
(DSW-100-TAx, -TAHx) |
- |
CO2 sensor
(DSW-200-CO2) |
|
Indoor Temperature Sensor DSW-100-Txx | |
(*) Available for the DSW-100-TA. |
|
Indoor Humidity Sensor DSW-100-Hx |
|
DSW-100 |
-H |
|
|
Measurement target |
-H |
|
Humidity |
Output spec. |
|
2-wire |
W4 |
4-wire |
|
|
|
Indoor Temperature/Humidity Sensor DSW-100-TxHx |
|
(*) Available for the DSW-100-TRH. |
|
Indoor CO2 Sensor DSW-200-CO2-xxx |
|
|
|
Temperature/Humidity Sensor Spec |
Rating |
Measurement Range |
DSW-100-Txx |
0 to 50 |
DSW-100-Hx |
5 to 90 %RH |
DSW-100-TxHx |
Temperature: 0 to 50, Humidity: 5 to 90 %RH |
|
Output |
DSW-100-TRx |
100/0 (Pt100) 3-wire type |
DSW-100-TAx |
4 to 20 mA DC (Linear conversion corresponding to 0 to 50)
2-wire or 4-wire types, selectable
Max allowable load: 500 or less |
DSW-100-Hx |
4 to 20 mA DC (Linear conversion corresponding to 0 to 100 %RH)
2-wire or 4-wire types, selectable
Max allowable load: 500 or less |
DSW-100-TRHV W4 |
Temperature |
100/0 (Pt100) 3-wire type |
Humidity |
0 to 1 V DC (Linear conversion corresponding to 0 to 100 %RH)
4-wire type
Max allowable load: 500 or less |
DSW-100-TAHx |
Temperature |
4 to 20 mA DC (Linear conversion corresponding to 0 to 50)
2-wire or 4-wire types, selectable
Max allowable load: 500 or less |
Humidity |
4 to 20 mA DC (Linear conversion corresponding to 0 to 100 %RH)
2-wire or 4-wire types, selectable
Max allowable load: 500 or less |
0 to 1 V DC (Linear conversion corresponding to 0 to 100 %RH)
4-wire type
Max allowable load: 500 or less |
|
Supply Voltage |
DSW-100-TRx |
No power needed |
DSW-100-TAx |
24 V DC10% |
DSW-100-Hx |
DSW-100-TxHx |
|
|
|
General Structure |
Element Type |
DSW-100-Txx |
RTD 100/0 (Pt100) |
DSW-100-Hx |
Electrostatic capacity variation type |
DSW-100-TxHx |
Temperature |
RTD 100/0 (Pt100) |
Humidity |
Electrostatic capacity variation type |
|
Mounting |
To the outlet box (inside wall), via outlet box cover: mounting dimension: 66.7 mm (JIS-C8340: 1999). |
Material |
Flame-resistant PC resin, Color: White |
|
Performance |
Accuracy |
DSW-100-TRx |
(0.1+0.0017|t|) |
DSW-100-TAx |
0.5 |
DSW-100-Hx |
5 %RH (at 5 to 45), Outside of 5 to 45: Max. 8 %RH |
DSW-100-TRHx |
Temperature |
(0.1+0.0017|t|) |
Humidity |
5 %RH (at 5 to 45), Outside of 5 to 45: Max. 8 %RH |
DSW-100-TAHx |
Temperature |
0.5 |
Humidity |
5 %RH (at 5 to 45), Outside of 5 to 45: Max. 8 %RH |
|
Response Characteristics |
DSW-100-Txx |
63 % response within 1 minute (at 1.5 m/s wind velocity) |
DSW-100-Hx |
Approx. 20 seconds (90 % change can be reached within 1 minute in 30-85 %RH range.) |
DSW-100-TxHx |
Temperature |
63 % response within 1 minute (at 1.5 m/s wind velocity) |
Humidity |
Approx. 20 seconds (90 % change can be reached within 1 minute in 30-85 %RH range.) |
|
|
|
Other |
Power consumption |
2-wire type: Approx. 550 mW (Output 4 to 20 mA DC)
4-wire type: Approx. 3 W (DSW-100-H W4)
4-wire type: Approx. 4 W (DSW-100-TA W4, DSW-100-TAH W4) |
Operating Environment |
Temperature: 0 to 50
Humidity: 5 to 90 %RH (non-condensing) |
Storage Environment |
Temperature: -20 to 60
Humidity: 5 to 90 %RH (non-condensing) |
Weight |
Approx. 90 g |
Insulation Resistance |
Case-Output: 500M or more, at 500 V DC |
Dielectric Strength |
Case-Output: 1.5 kV for 1 minute, 3 mA or less |
Accessories Included |
Sensor main unit mounting screw (M3 x 4): 4 pieces
Mounting plate: 1 piece
Mounting plate screw (M4 x 8, Spring washer): 2 pieces each
Instruction manual: 1 copy |
Environmental Specification |
RoHS directive conformance |
|
|
|
|
Rating |
Measurement Range |
DSW-200-CO2-1xx |
360 to 2000 ppm
(with Sensor Correction Function) |
DSW-200-CO2-2xx |
360 to 5000 ppm
(with Sensor Correction Function) |
|
Output |
DSW-200-CO2-x1x |
4 to 20 mA DC |
DSW-200-CO2-x2x |
0 to 20 mA DC |
DSW-200-CO2-x3x |
1 to 5 V DC |
DSW-200-CO2-x4x |
0 to 5 V DC |
DSW-200-CO2-x5x |
0 to 1 V DC |
<Output of CO2 Sensor>
For each range of CO2 concentration,linearly outputs
corresponding to CO2 concentration. However, if the measured value is lower than
360 ppm,the value corresponding to 360 ppm will be output.
|
Supply Voltage |
24 V DC10% |
|
|
General Structure |
Measurement Method |
Non dispersive infrared (NDIR) |
Mounting |
To the outlet box (inside wall), via outlet box cover: mounting dimension: 66.7 mm (JIS-C8340: 1999). |
Material |
Flame-resistant PC resin, Color: White |
|
|
Performance |
Accuracy |
(50ppm + 3 % of measured value).
Warm-up period: 30 minutes
Note:
Accuracy described here is the accuracy
of factor
shipment.
Accuracy after shipment changes. |
Response Characteristics |
Within 120 seconds |
Sensor Correction |
One cycle is equivalent
to 45 days, and if the measured value drops below
400 ppm in the current cycle, the lowest value
in the current cycle will become 400 ppm in the
next cycle, and the difference between the lowest
value and 400 ppm will be added to all other measured
values in the next cycle.
|
|
|
Other |
Power Consumption |
Approx. 3 W |
Operating Environment |
Temperature: 0 to 50
Humidity: 0 to 95 %RH (non-condensing) |
Storage Environment |
Temperature: -30 to 70
Humidity: 0 to 95 %RH (non-condensing) |
Weight |
Approx. 100 g |
Insulation Resistance |
Case-Output: 500 M or more, at 500 V DC |
Dielectric Strength |
Case-Output: 1.5 kV for 1 minute, 3 mA or less |
Accessories |
Sensor main unit mounting screw (M3 x 4): 4 pieces
Mounting plate: 1 piece
Mounting plate screw (M4 x 8, Spring washer): 2 pieces each
Instruction manual: 1 copy |
Environmental Specification |
RoHS directive conformance |
|
|
|
|
DSW-100-TR
|
DSW-100-TA
|
DSW-100-TA W4
|
|
DSW-100-H
|
DSW-100-H W4
|
DSW-100-TAH
|
DSW-100-TAH W4
|
DSW-200-CO2-□□□
|
|
|
|
|